Conveyor Systems

Conveyor Systems

Conveyor Belt Systems and Components

Conveyor systems keep products moving continuously, safely and under control on food, packaging, bottling and logistics lines. From Kahramankazan, Ankara, Zincir Gross supplies modular plastic belts, PVC/PU belts, and acetal and stainless steel belts / flat top chains. The right belt type depends on the product conveyed, the operating temperature, hygiene requirements and the drive method.

Modular, PVC and Acetal Stainless Belts

The table below summarises the product groups in our conveyor components category and their typical applications. Please see the relevant product page for details.

Product group Material / type Key features Typical use
Modular Belts PP, PE or POM (acetal) plastic modules Interlocking modules, positive drive by sprockets, open or closed surface, repair by replacing modules Food, packaging, bottling
PVC Belts PVC and PU belts Smooth closed surface, friction drive over drums, light to medium products Packaging, logistics; PU usually for oily foods
Acetal Stainless Belts Acetal (POM) modules with stainless steel pins; AISI 430/431 and AISI 304 flat top chains Pitch 38.1 mm, working load 6,000 N, slat widths from 57.1 mm to 190.5 mm Hygienic, wear-resistant conveying, bottle and packaging lines

Stainless steel flat top chain series

Series Material References Slat width Pitch Working load
812 AISI 430 / AISI 431 SS812 K225 … K750 57.1–190.5 mm 38.1 mm 6,000 N
815 AISI 304 / reinforced AISI 430 SS815 K225 … K750 57.1–190.5 mm 38.1 mm 6,000 N

Technical selection criteria

  • Product and load: The weight and size of the product and the total load on the line directly determine the belt type and material.
  • Operating temperature: In cold stores, freezing or hot-fill applications, the temperature range of the material is decisive.
  • Drive method: Modular belts and flat top chains are positively driven by sprockets; PVC/PU belts run by friction over drums.
  • Surface design: An open surface allows drainage, washdown and airflow; a closed surface suits small or delicate products.
  • Hygiene and cleaning: Food lines call for easy-to-clean surfaces and corrosion-resistant materials.
  • Ambient conditions: Water, oil, fatty foods or cleaning chemicals influence the choice of material.
  • Maintenance: With modular belts, damaged modules can be replaced individually, which can reduce downtime.

Materials: PP, PE, OM, PVC/PU and stainless steel

  • PP (polypropylene): A general-purpose modular belt material; the typical operating range is approximately +5 °C to +100 °C.
  • PE (polyethylene): Stays flexible at low temperatures; usable down to approximately −70 °C, so it is preferred for cold and freezer applications.
  • POM (acetal): Low friction and wear-resistant; the typical range is approximately −40 °C to +90 °C.
  • PVC and PU: Provide a smooth belt surface; PU is usually better suited to oily and fatty foods.
  • Stainless steel: Series 812 is made of AISI 430/431, series 815 of AISI 304 or reinforced AISI 430.

The temperature values given are approximate and may vary by manufacturer and application. For food-contact applications, materials should comply with the applicable regulations; you can request conformity documents when asking for a quote.

Frequently asked questions

Modular belts are the stronger option on food and bottling lines that require washdown, drainage and positive drive. On packaging and logistics lines carrying light to medium products on a smooth surface, PVC/PU belts are usually an economical solution.

Yes. On modular belts, damaged modules can be replaced to repair the belt, so there is no need to renew the entire belt.

Series 812 and 815 in the catalogue on our site have a pitch of 38.1 mm, a working load of 6,000 N and slat widths from 57.1 mm to 190.5 mm.
Send us your product, dimensions and operating conditions so we can identify the right conveyor for your line; request a quote.